fairly epic weapon :-)
I wasnt sure where to post this gven theres more sub boards than members these days :rofl:
Good decision (although you ditch the switchgear on race bikes don't you) :rofl:
Like the finished paint job :afro:
Lovely stuff
So what's the spec on this one mark? Stock motor or has seton been fiddling with it?
looks the tits mate :afro:
Quote from: The Wizard of MOz on June 07, 2019, 08:04:18 PM
Good decision (although you ditch the switchgear on race bikes don't you) :rofl:
:rofl: :rofl: :rofl:
Looks epic! :afro: I would never be able to use half of the abilities of a machine like that.
Quote from: The Wizard of MOz on June 07, 2019, 08:04:18 PM
Good decision (although you ditch the switchgear on race bikes don't you) :rofl:
Like the finished paint job :afro:
Cheers fella, turned out OK after the battleship grey remarks lol
Quote from: 1-600-matt on June 10, 2019, 08:04:40 AM
So what's the spec on this one mark? Stock motor or has seton been fiddling with it?
Motor wise its got some refinements -- YEC loom, Fiddled with Fuelling Maps, Braking Maps, SCS maps, TC maps and AW maps, MWR filter, YEC springs and Valves, and a full Ti system, just shy of 210bhp on he dyno (against 206 on my last one), 96ft lb ... Drives like a train :-)
That is loverly :cheesy:
Quote from: mc101 on June 24, 2019, 01:45:42 PM
Quote from: 1-600-matt on June 10, 2019, 08:04:40 AM
So what's the spec on this one mark? Stock motor or has seton been fiddling with it?
Motor wise its got some refinements -- YEC loom, Fiddled with Fuelling Maps, Braking Maps, SCS maps, TC maps and AW maps, MWR filter, YEC springs and Valves, and a full Ti system, just shy of 210bhp on he dyno (against 206 on my last one), 96ft lb ... Drives like a train :-)
Brakes and wheels don't look stock!?
It's only 100hp more than my zx6!!
Quote from: 1-600-matt on June 26, 2019, 12:27:35 AM
Quote from: mc101 on June 24, 2019, 01:45:42 PM
Quote from: 1-600-matt on June 10, 2019, 08:04:40 AM
So what's the spec on this one mark? Stock motor or has seton been fiddling with it?
Motor wise its got some refinements -- YEC loom, Fiddled with Fuelling Maps, Braking Maps, SCS maps, TC maps and AW maps, MWR filter, YEC springs and Valves, and a full Ti system, just shy of 210bhp on he dyno (against 206 on my last one), 96ft lb ... Drives like a train :-)
Brakes and wheels don't look stock!?
It's only 100hp more than my zx6!!
Oh I was answering the question just about the motor ...
Suspension KTEC all round (35mm DDS Catridges and KTEC DDS Shock)
Brembo GP4 RX
Brembo Z04 Pads
Brembo RCS Master Cylinder
Pitlane Limiter
Modified Swing Arm (+20mm)
OZ Forged Rims
Brembo Superbike Discs
AIM Solo 2
Ohlins Steering Damper (replace electronic OEM)
Lithium Battery
CRC Plastics
25 Degree QA Throttle
Clip ons
Seton Bell Mouth Kit
Forged Switch Gear
Seton Rear Sets
GBR Covers
DID 525 Chain
Carbon Clock Bracket
Lockstops
Braided lines throughout (Venhill)
Dunlop KR moto2 slicks
Renthal Sprockets
Ti engine bolt kit
Ti caliper kit
Ti discs and sproker bolt kit
Ti Fork bolt kit
Moto Holders rear subframe
Seton Chain Adjusters
Seton Paddock Lifters
Seton Sharks Fin (machined ally)
:-)
............ and I'm spent :rofl:
Quote from: The Wizard of MOz on June 26, 2019, 11:33:53 AM
............ and I'm spent :rofl:
:cheesy: :cheesy:
ps did you folks get my cheque yet ?
Quote from: mc101 on June 07, 2019, 07:43:38 PM
fairly epic weapon :-)
I wasnt sure where to post this gven theres more sub boards than members these days :rofl:
Is that a Chalkies job..? Looks :cool:
My mates just had a custom job on his ZX10R looks really good and seems good VFM.
(https://live.staticflickr.com/65535/48134201352_806e535f79_b.jpg) (https://flic.kr/p/2gksn6j)ZX10R (https://flic.kr/p/2gksn6j) by Jimhas7 (https://www.flickr.com/photos/88877547@N06/), on Flickr
Quote from: mc101 on June 26, 2019, 11:50:09 AM
Quote from: The Wizard of MOz on June 26, 2019, 11:33:53 AM
............ and I'm spent :rofl:
:cheesy: :cheesy:
ps did you folks get my cheque yet ?
Yes. Confirmation sent to your racing email address. Did you get that?
Quote from: The Wizard of MOz on June 26, 2019, 09:36:58 PM
Quote from: mc101 on June 26, 2019, 11:50:09 AM
Quote from: The Wizard of MOz on June 26, 2019, 11:33:53 AM
............ and I'm spent :rofl:
:cheesy: :cheesy:
ps did you folks get my cheque yet ?
Yes. Confirmation sent to your racing email address. Did you get that?
I didnt fella but so long as you've got the paperwork etc I dont really need it etc ...
Quote from: Jimhas7 on June 26, 2019, 09:11:49 PM
Quote from: mc101 on June 07, 2019, 07:43:38 PM
fairly epic weapon :-)
I wasnt sure where to post this gven theres more sub boards than members these days :rofl:
Is that a Chalkies job..? Looks :cool:
My mates just had a custom job on his ZX10R looks really good and seems good VFM.
(https://live.staticflickr.com/65535/48134201352_806e535f79_b.jpg) (https://flic.kr/p/2gksn6j)ZX10R (https://flic.kr/p/2gksn6j) by Jimhas7 (https://www.flickr.com/photos/88877547@N06/), on Flickr
Indeed it is .. Craigs done my stuff for a few years now -- paint at Padded Cell then off to Craig for stickers/branding