As per the title ..... how the feck are you meant to get the bike up without it falling over!!! :BangHead:
Tried and tried, every time we go to lift the back end, the pin that goes into the back spine starts to come out and the bike wobbles, what a pain in the arse!!
Can anyone explain the knack of working these feckers ............. please :grin:
Never had an issue with mine on the Speed, it is a Honda specific one or a generic one? sometimes the arm that holds the pin can be set slightly off upright so that the bike tends to slide onto not off the Pin if you see what I mean.
Other than that it's probably just a case of getting the 'knack' of using it.
Must admit I too was nervous about using a paddock stand when I first got one, but you do get the knack. I have R&G cotton reals on the swing arm, that helps, I get the stand on the reals whilst the bike is on its side stand then push the bike umpiring hot with my left hand whilst pulling the paddock stand down with my right hand. That works for me.
Just remember to keep your side strand down for when you take the bike off the stand
Removing the bike, pull the stand up with right hand.... Slowly mind you, and hold the rear of the bike with your left, as the stand comes away from the bike tip the bike towards you with your left hand and she should settle on her side stand..... Hence the need to ensure the side stand us down.
Hope this helps
Steve
Quote from: Green_Ninja on September 27, 2013, 11:44:04 PM
it is a Honda specific one or a generic one? sometimes the arm that holds the pin can be set slightly off upright so that the bike tends to slide onto not off the Pin if you see what I mean.
Other than that it's probably just a case of getting the 'knack' of using it.
its a generic stand, but with a pin that is meant to be specific to the bike. We have tried it going from the side stand and with me holding the bike upright and my hubby working the stand. Each time as soon as you start to put pressure on the stand, the pin starts to slide back out and the bike starts to fall over!
Will try again and see if there is any way to adjust the angle, or see if we can get it to grip it at all.
cheers
Quote from: cbr6y on September 28, 2013, 08:14:55 AM
Quote from: Green_Ninja on September 27, 2013, 11:44:04 PM
it is a Honda specific one or a generic one? sometimes the arm that holds the pin can be set slightly off upright so that the bike tends to slide onto not off the Pin if you see what I mean.
Other than that it's probably just a case of getting the 'knack' of using it.
its a generic stand, but with a pin that is meant to be specific to the bike. We have tried it going from the side stand and with me holding the bike upright and my hubby working the stand. Each time as soon as you start to put pressure on the stand, the pin starts to slide back out and the bike starts to fall over!
Will try again and see if there is any way to adjust the angle, or see if we can get it to grip it at all.
cheers
Post up a pic of the stand or link to it
What bike you got Lorna?
Quote from: Green_Ninja on September 28, 2013, 10:30:45 AM
Post up a pic of the stand or link to it
http://www.toolstop.co.uk/sealey-rps3-single-sided-rear-support-stand-p54112
this is the one I have!
Thinking on the bobbins option, I spoke to a bike shop this morning and they didn't think that bobbins can be fitted to the CB, but R&G do sell them for it, so a bit bemused here :undecided:
Quote from: Jarse on September 28, 2013, 11:28:45 AM
What bike you got Lorna?
Hugh
Got a CB1000R :cool: :cool:
Very, very nice :moto:
just been out and tried again ... fail
It looks like the pin is too small, its wobbling around in the chamber, hence why every time you put pressure on it, it slides.
Checked the website and the pin for the Honda looks exactly the same as the one I have. Can only guess it may fit some Hondas, just not this one!!
Looks like a new paddock stand and bobbins then.
Quote from: Jarse on September 28, 2013, 05:37:30 PM
Very, very nice :moto:
cheers Hugh, I love it!!
It's pimps.
You may find it easier with bobbins I know I do, and a set if bobbins and new stand is cheaper than dropping the bike
CB1000R....... Very nice indeed...... What colour?
ordered the bobbins last night, will pick up another stand locally. Yes definitely much cheaper than dropping the bike, don't fancy that much!!
Bike is black n very shiny :cool: :cool:
Quote from: cbr6y on September 28, 2013, 05:38:52 PM
just been out and tried again ... fail
It looks like the pin is too small, its wobbling around in the chamber, hence why every time you put pressure on it, it slides.
Checked the website and the pin for the Honda looks exactly the same as the one I have. Can only guess it may fit some Hondas, just not this one!!
Looks like a new paddock stand and bobbins then.
Quote from: Jarse on September 28, 2013, 05:37:30 PM
Very, very nice :moto:
cheers Hugh, I love it!!
you should be able to get the correct PIN, cheaper than a new stand and I assume the bobbins option is either side of the rear wheel through the axle which means that will be fine for cleaning but you'll be buggered if you need to take the rear wheel off.
The PIN should be a good fit, no slop.
Lorna if you can get a size of the bore and let me have the pin i can 'turn' you a new one on the lathe at work... :)
Quote from: Glennmac7 on September 30, 2013, 01:16:23 AM
Lorna if you can get a size of the bore and let me have the pin i can 'turn' you a new one on the lathe at work... :)
Good man :azn:
fantastic Glenn, the diameter of the bore is 2.8cm and the overall length is 25cm. The bore does get bigger part way through, then reduces again. 1st point of change is at about 13cm in.
Let me know how best to get the pin to you?
cheers :azn:
Glenn
cheers for the offer buddy, but I have managed to source one for just shy of a tenner delivered, so no need for you to go to the effort, thanks all the same!
good to know you can do stuff like that for future.
Apparently the one I have is for a ducati going by size (ducati shop says there are two sizes for their bikes), so if anyone is looking for a 22-23mm diameter pin for a sealey single arm paddock stand, I can help!!
cheers peeps
Glad to hear you've got it sorted :azn:
Ok Lorna. Glad you got it sorted. That would have been no bother though... :grin:
was great of you to offer Glenda, much appreciated!!
well so much for that!!
New pin arrived, and it does go inside the sleeve and appears to be a fairly good fit (diameter) but its not long enough. Bike still started to slide off the pin when bike at a slight angle, I just don't trust it.
So Glenn ... as I was saying, how best to get the pin to you ?? :rofl:
:cheesy: :rofl: Well I can meet in Glasgow when your next up. Or pop by mine. Or send it? Either way take pics and detail what ye want done. Can put a thread and supply a bolt in it for extra piece of mind too. :tongue:
Easiest thing is probably to drop it over to you, its not as if you are that far away.
Will get pics etc and give ya a shout!!
cheers
:cool: